GC 7003, an online gas pretreatment model (compressor cooler) independently produced and developed by SIGAS, has obtained the Chinese Academy of Metrological Sciences' authoritative certification. This product's dehumidification efficiency reaches 98.9%, and the SO2 dissolution loss rate is only 1.6%, which beats the imported similar products with high-cost performance and quality!
"China Institute of Metrology" is the highest metrology research center and national legal metrology technical organization. In 2011, the Chinese Institute of Metrology and the China National Accreditation Service for Conformity Assessment signed a memorandum of understanding on technical evaluation activities in the accreditation field, recognizing the metrology support role of the Chinese Institute of Metrology and issued calibration/test results and traceability effectiveness.
SIGAS GC 7003 online gas pretreatment is a piece of economical equipment and a necessary product in gas analysis. In recent years, the environmental protection industry mainly uses high humidity and a large gas analysis flow. A large amount of water has dissolved the measured gas that needs to be analyzed, leading to inaccurate test data and high maintenance costs. Under the dehumidification requirements at the flow rate of 7N/min, one set of the system's efficiency can meet the original double-channel heat exchange system used in series.
Product characteristics:
1.GTL heat exchange technology effectively improves the heat exchange efficiency. Without increasing the pressure drop and gas resistance, the liquid is virtually taken out of the gas.
2. The power of the system is increased by 25%. A dehumidifier is equipped with a two-flow heat exchange pipe and a peristaltic pump.
3. Compact size, save space, weight less than 10KG.
4. One key to restore factory settings.
Product parameters:
1. System power: about 38W
2. Maximum inlet dew point temperature: 80℃
3. Sample gas inlet temperature: 180℃
4. Heat exchanger: GTL heat exchanger (glass material) pressure drop
5. Maximum allowable flow: 300NL/ H
6. Sample gas interface: DN 4/6 PTFE
7. Cold liquid interface: DN 4/6 PTFE
8. Ambient temperature: 45℃
9. Ambient humidity: 95%RH
10. Status indicator light: red fault; green run
11. Preheating time: ≤10min
12. Volume: 222*222*300mm
13. Weight: ≤ 9.5kg
14. Power supply: 220V 50HZ
GC 7003, an online gas pretreatment model (compressor cooler) independently produced and developed by SIGAS, has obtained the Chinese Academy of Metrological Sciences' authoritative certification. This product's dehumidification efficiency reaches 98.9%, and the SO2 dissolution loss rate is only 1.6%, which beats the imported similar products with high-cost performance and quality!
"China Institute of Metrology" is the highest metrology research center and national legal metrology technical organization. In 2011, the Chinese Institute of Metrology and the China National Accreditation Service for Conformity Assessment signed a memorandum of understanding on technical evaluation activities in the accreditation field, recognizing the metrology support role of the Chinese Institute of Metrology and issued calibration/test results and traceability effectiveness.
SIGAS GC 7003 online gas pretreatment is a piece of economical equipment and a necessary product in gas analysis. In recent years, the environmental protection industry mainly uses high humidity and a large gas analysis flow. A large amount of water has dissolved the measured gas that needs to be analyzed, leading to inaccurate test data and high maintenance costs. Under the dehumidification requirements at the flow rate of 7N/min, one set of the system's efficiency can meet the original double-channel heat exchange system used in series.
Product characteristics:
1.GTL heat exchange technology effectively improves the heat exchange efficiency. Without increasing the pressure drop and gas resistance, the liquid is virtually taken out of the gas.
2. The power of the system is increased by 25%. A dehumidifier is equipped with a two-flow heat exchange pipe and a peristaltic pump.
3. Compact size, save space, weight less than 10KG.
4. One key to restore factory settings.
Product parameters:
1. System power: about 38W
2. Maximum inlet dew point temperature: 80℃
3. Sample gas inlet temperature: 180℃
4. Heat exchanger: GTL heat exchanger (glass material) pressure drop
5. Maximum allowable flow: 300NL/ H
6. Sample gas interface: DN 4/6 PTFE
7. Cold liquid interface: DN 4/6 PTFE
8. Ambient temperature: 45℃
9. Ambient humidity: 95%RH
10. Status indicator light: red fault; green run
11. Preheating time: ≤10min
12. Volume: 222*222*300mm
13. Weight: ≤ 9.5kg
14. Power supply: 220V 50HZ
